Volkswagen Golf ll, Jetta II

1983-1992 of release

Repair and car operation

Volkswagen Golf 2 / Jett 2
+ 1.1. Short technical characteristics of diesel engines
+ 2. Engine
+ 3. Power supply system
+ 4. Coupling
+ 5. Transmission
+ 6. Transmission
+ 7. Forward drive
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
- 12. Electric equipment
   12.1. Block of safety locks and relay
   + 12.2. Generator
   + 12.3. Starter
   + 12.4. Forward headlight
   12.5. Replacement of a lamp of the forward index of turn
   12.6. Replacement of lamps of a back lamp
   12.7. Replacement of a lamp of illumination of registration plate
   + 12.8. Windscreen screen wiper
   + 12.9. Screen wiper of a door of a back
   12.10. Adjustment of a jet of washers of glasses
   12.11. Combination of devices
   12.12. Block of control lamps
   + 12.13. Ignition system
   + 12.14. Electric circuits

12.11. Combination of devices

GENERAL INFORMATION

Dashboard details

1–facing of a combination of devices;

2–dashboard;

3–screw

Fastening of a combination of devices

1–dashboard;

2–screw;

3–combination of devices;

4–ledge

Cable of a drive of a speedometer

1–speedometer cable;

2–bracket of fastening of a cable

Voltage stabilizer

1–positive contact;

2–negative contact;

3–voltage stabilizer

Installation of the light diode

1–negative contact;

2–light diode

Speedometer fastening

Tachometer fastening

1–the screw of fastening of the index of temperature of cooling liquid;

2–screw of fastening of the index of level of fuel;

3–screw of fastening of a tachometer;

4–spring latch

Case of a nest of a connecting block

1–level;

2–ledge;

3–nest case

Removal of the case of a nest of a connecting block

1–latch;

2–flexible tire;

3–case of a nest of a block

Multipurpose index of VDO firm

1–index fastening

Multipurpose index of Motometr firm

1–index fastening;

2–latch

Printed-circuit board of control of pressure of oil

1–latch;

2–printed-circuit board

Connection of hours

1–negative tire;

2–clip

Removal

PERFORMANCE ORDER

1. To disconnect a wire from the "minus" plug of the storage battery.

2. To unscrew screws 2 (see fig. Fastening of the top shelf) fastenings of the left shelf under the dashboard and to pull out the shelf 1 down to the left.

3. To take out all switches from facing 1 (see fig. Dashboard details) combinations of devices. For this purpose to insert a thin screw-driver into a crack between facing and the switch, from below the switch. A screw-driver to turn the switch up and to take out it from a nest.

4. To disconnect from the switch a connecting block with wires. Each block can be established only on one switch therefore at installation of switches of a block it is impossible to mix.

5. To remove the handle 1 (see fig. The mechanism of management of a heater) with a washer 2.

6. To pull out handles 12.

7. To remove the panel 3.

8. To unscrew screws of 4 fastenings of an arm of 5 levers, to pull out an arm 5 forward and to disconnect from it ropes 6, 7 and 8.

9. To remove a radio receiver. If the car without a radio receiver to take out a cap from facing 1 (see fig. Dashboard details) combinations of devices.

10. To turn out screws 3 and to remove facing of 1 combination of devices.

11. To turn out screws 2 (see fig. Fastening of a combination of devices) and to incline combination of 3 devices, to deduce from gearing a ledge of 4 combinations. To push it is a little forward a combination 3.

12. To disconnect a cable of a drive of a speedometer from a combination of devices, for this purpose to compress a bracket of 2 fastenings (see fig. Cable of a drive of a speedometer).

13. To remove a vacuum hose with эконометра (if is).

14. To disconnect two 14-contact connecting blocks. For this purpose to insert a screw-driver between a block and a nest and carefully to take away a block from a nest that there was gearing a spring latch, and to take out a block from a nest.

15. To take out a combination of devices.

VOLTAGE STABILIZER

Check

The stabilizer supports constant tension in a combination of devices.

PERFORMANCE ORDER

1. Before check to disconnect a cable of a drive of a speedometer and a vacuum hose from эконометра.

2. All electric connecting blocks should be connected to a combination of devices. It is not necessary to disconnect a wire from the "minus" plug of the storage battery.

3. To connect the voltmeter to contacts 1 and 2 (see fig. A voltage stabilizer) and to include ignition. Tension of the stabilizer should be higher than 10 V.Esli it 10,5 In and below 9,5 In, сначит the stabilizer is faulty and it is necessary to replace it.

LIGHT DIODES

Installation

PERFORMANCE ORDER

At installation of light diodes 2 (see fig. Installation of the light diode) it is necessary to observe polarity. To reduce probability of a mistake, negative contact of 1 diode to unbend aside.

SPEEDOMETER

PERFORMANCE ORDER

To remove a speedometer, to turn out the screws noted by shooters on fig. Speedometer fastening.

TACHOMETER AND INDEXES OF LEVEL OF FUEL AND TEMPERATURE OF COOLING LIQUID

PERFORMANCE ORDER

To remove the index of temperature of cooling liquid, it is necessary to unscrew screws 1 (see fig. Tachometer fastening). To remove the index of level of fuel, it is necessary to unscrew the screw 2 and to pull out the index down. To remove a tachometer – to unscrew screws 3.

CASE OF THE NEST OF THE CONNECTING BLOCK

PERFORMANCE ORDER

1. To remove the nest case, it is necessary to wring out a screw-driver a level 1 (see fig. The case of a nest of a connecting block) cases so that it left gearing with ledges of 2 cases of a combination of devices, and to shift the case 3 in the arrow direction.

2. Through openings in the case 3 to deduce from gearing plastic latches 1 (see fig. Removal of the case of a nest of a connecting block) and to take out from the case 3 the flexible connecting tire 2.

MULTIPURPOSE INDEX

PERFORMANCE ORDER

1. To remove the multipurpose index, it is necessary to unscrew screws 1 (see fig. Multipurpose index of VDO firm or fig. Multipurpose index of Motometr firm).

2. At the index of Motometr to wring out a latch 2 in the direction specified by an arrow.

PRINTED-CIRCUIT BOARD OF CONTROL OF PRESSURE МАСЛА1

PERFORMANCE ORDER

To remove a payment 2 (see fig. The printed-circuit board of control of pressure of oil) control of pressure of oil, it is necessary to wring out latches 1.

CONNECTION OF CONNECTING TYRES BY O'CLOCK

In a combination of devices depending on a complete set instead of a tachometer hours can be established. In this case two flexible tires join them.

PERFORMANCE ORDER

The tire 1 (see fig. Connection of hours) on weight is inserted under a screw head and clamped of. The positive tire puts on on contact of hours and nestles a plastic clip 2.