|
RELEASE MODELS TO 07.1987 G. (A MIRROR WITH MANUAL ADJUSTMENT)
External rear-view mirror with manual adjustment of release to 07.1987 g.
1–handle;
2–protective casing;
3–nut;
4–arm;
5–adjustment mechanism; |
6–laying;
7–decorative casing;
8–mirror;
9–screw;
10-bolt |
Removal
| PERFORMANCE ORDER |
| 1. To remove the handle 1. |
| 2. To remove a protective casing 2. |
| 3. To remove an upholstery of the panel of a door (see subsection 11.16). |
| 4. To unscrew a nut 3. |
| 5. To remove a decorative casing 7. |
| 6. To unscrew screws 9. |
| 7. To remove a mirror 8 together with the mechanism of adjustment 5. |
|
Installation of an external rear-view mirror make as it should be, the return to removal.
RELEASE MODELS AFTER 07.1987 G. (A MIRROR WITH MANUAL ADJUSTMENT)
With 08.1987 there were changes in a design of fastening of a mirror to a body and fastenings of a reflecting element in the case.
External rear-view mirror with manual adjustment of release from 07.1987 g.
1–a reflecting element;
2–adjusting pin;
3–mechanism;
4–case;
5–decorative insert;
6–laying;
7–screw;
8–pin; |
9–door frame;
10-handle;
11-percussion cap;
12-protective casing;
13-nut;
14-arm;
15-adjustment mechanism |
Removal and installation
| PERFORMANCE ORDER |
|
|
1. At dismantle of a reflecting element to paste slices of an insulating tape 1 on the case of 4 mirrors to protect the case. To hook reflecting element 3 a wooden shovel 2 from below, and then from above and to take out it from the case 4. |
| 2. To establish reflecting element pins 2 (see fig. An external rear-view mirror with manual adjustment of release from 07.1987 g) in seats and accurately to press on the middle of a reflecting element 1 so that it rose into place. |
| 3. Other actions on removal and installation of a mirror are similar to early release (see above). |
|
RELEASE MODELS TO 07.1987 G. (A MIRROR WITH ELECTRIC ADJUSTMENT)
Mechanism of the electric drive of adjustment
|
|
1–screw;
2–electric motor;
3–case;
4–wires |
Removal
| PERFORMANCE ORDER |
|
|
1. To turn a clamp 2 by means of a screw-driver 1 in the direction specified by an arrow. To take out reflecting element 3 of the case 4. |
| 2. To turn off screws 1 (see fig. Mechanism of the electric drive of adjustment). |
| 3. To remove the electric motor 2. |
| 4. To disconnect wires 4. |
| 5. To remove the switch from an upholstery of the panel of a door. |
| 6. To disconnect a block. |
| 7. To remove an upholstery of the panel of a door (see subsection 11.16). |
| 8. To remove a protective film. |
| 9. To weaken a collar of fastening of wires. |
| 10. To separate contacts of wires |
| 11. To unscrew screws of fastening of the case of a mirror to a door and to remove it. |
|
Installation
| PERFORMANCE ORDER |
| 1. Installation of an external rear-view mirror make as it should be. At installation to connect wires to the electric motor according to color. |
| 2. To paste a protective film by means of a bilateral gluing tape. |
|
|
3. To turn against the stop a clamp 2 in the direction specified by an arrow. To establish reflecting element 3 in the case 4. To turn a clamp 2 by means of a screw-driver 1 in the direction opposite to the direction arrows. |
|
|