Volkswagen Golf ll, Jetta II

1983-1992 of release

Repair and car operation


Volkswagen Golf 2 / Jett 2
+ 1.1. Short technical characteristics of diesel engines
+ 2. Engine
+ 3. Power supply system
+ 4. Coupling
+ 5. Transmission
+ 6. Transmission
+ 7. Forward drive
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
- 12. Electric equipment
   12.1. Block of safety locks and relay
   + 12.2. Generator
   + 12.3. Starter
   + 12.4. Forward headlight
   12.5. Replacement of a lamp of the forward index of turn
   12.6. Replacement of lamps of a back lamp
   12.7. Replacement of a lamp of illumination of registration plate
   + 12.8. Windscreen screen wiper
   + 12.9. Screen wiper of a door of a back
   12.10. Adjustment of a jet of washers of glasses
   12.11. Combination of devices
   12.12. Block of control lamps
   - 12.13. Ignition system
      - 12.13.1. Classical system of ignition
         12.13.1.1. Removal and installation of the distributor of ignition
         12.13.1.2. Check of contacts of the breaker
         12.13.1.3. Replacement of contacts of the breaker
         12.13.1.4. Check and adjustment of a corner of the closed condition of contacts
         12.13.1.5. Gap adjustment between contacts
         12.13.1.6. Adjustment of a corner of an advancing of ignition
         12.13.1.7. Survey of a cover of the distributor
         12.13.1.8. Check of a centrifugal regulator of the distributor of ignition
         12.13.1.9. Check of the vacuum proof-reader of the distributor of ignition
         12.13.1.10. Check of the coil of ignition
         12.13.1.11. Check of spark plugs
      + 12.13.2. Transistor system of ignition
   + 12.14. Electric circuits

12.13.1. Classical system of ignition

12.13.1.1. Removal and installation of the distributor of ignition

Removal

PERFORMANCE ORDER
1. To disconnect a wire from the "minus" plug of the storage battery.
2. To disconnect high-voltage wires from a cover 1 (see fig. Ignition distributor) distributor.
3. To disconnect a vacuum hose from the vacuum proof-reader 19.
4. To disconnect a wire from the plug of a low voltage sideways the distributor.
5. To uncover 1 distributor, having removed previously the screen 21.
6. To establish the piston of the first cylinder in VMT (see subsection 2.2.1 item 5 for engines in volume of 1,1 and 1,3 l or subsection 2.2.2 item 9 for engines in volume of 1,6 l). Thus the begunok should stop opposite to a label (dredging on the case) the distributor, as is shown in drawing.
7. To unscrew bolts 20 (see fig. The ignition distributor) (at the engine in volume of 1,6 l to turn out a bolt of fastening of the holder of the distributor) and to take out the ignition distributor.

Installation

PERFORMANCE ORDER
1. Establish the ignition distributor upside-down. At installation the crankshaft should be in the family way, at which the piston of the first cylinder is in VMT.
2. To turn a begunok that it was located opposite to a label on the distributor case.
3. At the engine in working volume of 1,6 l to turn the roller of a drive of the oil pump so that the ledge on the roller was located parallel to a cranked shaft of the engine.
4. If after distributor installation the begunok is located not against a label on the case, to turn the distributor and only after that to tighten bolts of fastening of the distributor.
5. After installation of the distributor to adjust a corner of an advancing of ignition.