Volkswagen Golf ll, Jetta II

1983-1992 of release

Repair and car operation

Volkswagen Golf 2 / Jett 2
+ 1.1. Short technical characteristics of diesel engines
- 2. Engine
   2.1. Removal and engine installation
   - 2.2. Dismantling and engine assembly
      + 2.2.1. Engines in volume of 1,1 and 1,3 l
      + 2.2.2. Engines in volume of 1,6 and 1,8 l
      - 2.2.3. Diesel engine
         2.2.3.1. Camshaft drive
         2.2.3.2. Removal and installation of a head of the block of cylinders
         2.2.3.3. Dismantling of a head of the block of cylinders
         2.2.3.4. Check and repair of a head of the block and its details
         2.2.3.5. Assembly of a head of the block of cylinders
         2.2.3.6. Adjustment of gaps between cams of a cam-shaft and levers of valves
         2.2.3.7. Technical condition of hydropushers of valves
         2.2.3.8. Intermediate shaft
         2.2.3.9. Flywheel
         2.2.3.10. Epiploons of a cranked shaft
         2.2.3.11. Oil case
         2.2.3.12. Oil pump
         2.2.3.13. Shatunno-porshnevaya group
         2.2.3.14. Cranked shaft
         2.2.3.15. Check of the block of cylinders
   + 2.3. System of greasing of the engine
   + 2.4. System of cooling of the engine
   + 2.5. System of production of the fulfilled gases
+ 3. Power supply system
+ 4. Coupling
+ 5. Transmission
+ 6. Transmission
+ 7. Forward drive
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
+ 12. Electric equipment

2.2.3.11. Oil case

GENERAL INFORMATION

Details of system of greasing of the diesel engine

1–masloslivny stopper;
2–sealing ring;
3–oil case;
4–bolt of fastening of a case;
5–case laying;
6–maslopriyemnik of the oil pump;
7–bolt of fastening of a maslopriyemnik;
8–sealing ring of a maslopriyemnik;
9–cover of the oil pump;
10-a conducted gear wheel;
11-case of the oil pump;
12-index of level of oil;
13-cover of a maslozalivny mouth;
14-sensor of pressure of oil;
15-bolt of fastening of the vacuum pump;
16-holder of the vacuum pump;

17-vacuum pump;
18-laying of the vacuum pump;
19-gear wheel of a drive of vacuum and oil pumps;
20-laying of an arm of the oil filter;
21-bolt of fastening of an arm;
22-arm of the oil filter;
23-sealing ring of a cooler;
24-oil cooler;
25-nut of fastening of a cooler;
26-oil filter;
27-pump roller;
28-bolt of fastening of a cover of the oil pump;
29-bolt of fastening of the oil pump

If the engine is removed from the car, to unscrew bolts of fastening of a case and to remove it together with laying.

If the engine is established on the car, to remove a case it is necessary in the following order:

PERFORMANCE ORDER

1. To turn out a stopper 1 and to merge oil from the engine. To wrap a stopper and to tighten the moment of 30 N · m (3,0 kgfs · м).

2. To tighten the hand brake.

3. To lift a jack a forward part of the car and to establish on supports.

4. To unscrew bolts 4 and to remove a case 3 with laying 5. Establish a case upside-down. At installation of a case to replace laying 5. Bolts 4 to tighten cross-wise the moment of 20 N of m (2,0 kgfs · м).