Volkswagen Golf ll, Jetta II

1983-1992 of release

Repair and car operation



Volkswagen Golf 2 / Jett 2
+ 1.1. Short technical characteristics of diesel engines
+ 2. Engine
+ 3. Power supply system
+ 4. Coupling
+ 5. Transmission
+ 6. Transmission
+ 7. Forward drive
+ 8. Steering
+ 9. Suspension brackets
+ 10. Brake system
+ 11. Body
- 12. Electric equipment
   12.1. Block of safety locks and relay
   + 12.2. Generator
   - 12.3. Starter
      12.3.1. Starter removal
      12.3.2. Starter dismantling
      12.3.3. Check of a technical condition
      12.3.4. Starter assembly
   + 12.4. Forward headlight
   12.5. Replacement of a lamp of the forward index of turn
   12.6. Replacement of lamps of a back lamp
   12.7. Replacement of a lamp of illumination of registration plate
   + 12.8. Windscreen screen wiper
   + 12.9. Screen wiper of a door of a back
   12.10. Adjustment of a jet of washers of glasses
   12.11. Combination of devices
   12.12. Block of control lamps
   + 12.13. Ignition system
   + 12.14. Electric circuits

12.3.2. Starter dismantling

GENERAL INFORMATION

Starter details

1–bolt;
2–washer;
3–bearing cover;
4–washer;
5–lock washer;
6–adjusting washer;
7–back bearing;
8–a cover from a collector;
9–shchetkoderzhatel;
10-a cover from a drive;
11-forward bearing;
12-bolt;
13-lock ring;
14-emphasis;
15-traction relay;
16-washer;
17-nut;
18-basic ring;
19-plug;
20-drive;
21-nut;
22-spring washer;
23-drive lever;
24-lever axis;
25-stator winding;
26-rotor;
27-brush;
28-screw of fastening of a pole;
29-plug of inclusion of a drive;
30-spring;
31-washer;
32-coupling bolt

Rotor removal

1–protective ring;

2–spring ring;

3–rotor shaft;

4–a cover from a drive


PERFORMANCE ORDER
1. To disconnect from the traction relay 15 (see fig. Starter details) conclusion of a winding of excitement.
2. To unscrew bolts 12 and to remove the traction relay 15, having deduced from gearing the lever 23.
3. To unscrew bolts 1 and to uncover 3 and a washer 4.
4. To remove a lock washer 5 and adjusting washers 6.
5. To unscrew bolts 32 and to uncover 8.
6. To pull out brushes 27 of a shchetkoderzhatel 9 and to remove a shchetkoderzhatel.
7. To remove the starter case with windings 25.
8. To lift the car.
9. To unscrew a nut 21, to take out an axis 24 levers and to remove the lever 23.
10. To take out a rotor 26 with a drive 20 of a cover 10, it is necessary to put a rotor with a cover vertically and, using a tube of suitable diameter as an opravka, to bring down a protective ring 1 (see fig. Rotor removal) from a spring ring 2.
11. To remove a spring ring 2 and to take out a rotor from a cover 4.
12. To clamp a rotor 26 (see fig. Starter details) in a vice and to remove from a rotor shaft a drive 20 assembled. The drive is not subject to dismantling. If it is faulty, it is necessary to replace it.